Cockpit Chronicles: Eight ways to slow a jet

One of my first posts on Cockpit Chronicles was an explanation on how to park a 757. At the risk of catering only to people who have recently acquired their own Boeing jets, I’d like to continue with another lesson.

The eight ways to slow a jet

When you’re driving your 5-speed manual transmission car and you exit an offramp, besides just taking your foot off the gas pedal, there are a couple of different ways that you can slow down. Most people probably put on the brakes, but you could also downshift as well.

In an airliner, there are four different ways inflight and four methods on the ground to slow a jet, and often these techniques can be used in conjunction.

Unlike turboprop airplanes, jets are rather difficult to slow down and require a bit of planning in advance to avoid burning too much fuel or ending up too high at the airport for landing.

So let’s start with our Boeing that’s at 33,000 feet. Pilots will use a rough “3 to 1” guide when deciding when they’ll need to start down, adjusting for wind as needed.

To do that, take the 33,000 feet, drop the zeros and multiply it by three. 33 X 3 = 99 miles.

So, for a descent at idle thrust, the pilots will need to start down within 99 miles of the airport. Any later and they’ll be too high and need to add drag to get down, and any sooner and they may need to add power and level off for a while. Either way, more fuel is burned.

A side note: If the engines were to fail, our airplane would likely be able to make it to the runway if it were within that 99 mile point. It’s just going to take some perfect planning on the part of the pilots, as was the case with the Air Transat and Air Canada flights.

Since an airplane burns far less fuel at altitude, it’s best to stay up high until the airplane can descend, ideally at idle thrust, all the way to the final approach segment. That’s our goal, subject to air traffic control requiring something different.

It’s not uncommon, especially in the U.S., for air traffic controllers to leave you at altitude past your normal beginning of descent point. In this case, it’s going to take more than idle thrust to descend quickly enough.Speed Brakes

In this situation, we can use speed brakes, which are the panels on top of the wing that move up equally on both wings to increase the drag on an airplane and reduce the lift.

So they’re the best method to initially increase the rate of descent and/or slow the airplane.

Since there are usually no airspeed limitations when using speed brakes, they can be deployed anytime they’re needed.

Flaps

The next method to slow an airplane involves using the flaps. These devices are panels that extend from the leading and trailing edges of the jet to change the shape of the wing to provide more lift. This allows a high-speed wing to quickly transform into a wing that can keep the jet in the air at much lower speeds.

In addition to creating more lift, flaps also create drag, and can slow a jet nicely. Unfortunately, we can’t begin to use the flaps until below 250 knots or so. Each step of the flaps has a different speed limit, above which too much stress will be placed on the flaps and a maintenance inspection would be necessary if that limit were exceeded.

We now have a program called FOQA, or Flight Operations Quality Assurance, that records the exact speed at which the flaps are deployed among many other parameters and sends a report to the company (see my personal experiences with FOQA here). Should the flap speed limits be exceeded, the airplane is taken out of service and given a thorough inspection, sometimes costing tens of thousands of dollars in maintenance man-hours to accomplish, not to mention the revenue lost when an airplane isn’t flying.

So let’s say that we’re flying into Miami or Los Angeles which are two airports known for the ‘slam dunking’ that ATC occasionally needs on certain arrivals.

Imagine that you’re now at 230 knots with the first notch of flaps extended and you still aren’t descending at a high enough rate. What can you do? More flaps would add drag, but you’ll need to be below 220 knots before you can go to flaps 5. And you’d better not hit a gust or any turbulence that sends you above 220 with those flaps out.

Landing Gear

So the next solution is the landing gear. This can be extended at any time you’re showing 270 knots or less of airspeed. They add a similar amount of drag as the spoilers, which are still extended in our scenario.

Pull up, pull up!

Finally, as with any airplane, our 4th method to decelerate is pretty basic; lift the nose up which initially decreases our rate of descent. We adjust the descent to slow the aircraft to bring the flaps out on schedule.

Often times there are points along an arrival where we’ll need to be at a certain speed and altitude. These ‘crossing restrictions’ are very important to meet and add another challenge for the arrival.


Pull Up, Pull Up!

Fortunately we don’t have to rely only on the 3 to 1 calculation to properly meet these targets when planning our descent. We can plug in the speed and altitude we want when flying over a waypoint into the FMS, or Flight Management System, that will calculate the time we should start down, using a function called VNAV, or Vertical Navigation.

Slowing down after landing – Ground Spoilers

Finally when we touch down, ground spoilers will automatically deploy from the top of the wings. This is done by using the same handle which deploy the same panels as the speed brakes, but now a few extra panels that open even further than the speed brakes are included.

These panels not only give us added drag, but when deployed, they add weight to the wheels which dramatically increases the effectiveness of our second method of stopping, the brakes.

Brakes!

All airliner brakes have anti-skid protection and the option to use ‘autobrakes’ for landing. We can preset the brakes before landing to automatically activate soon after we touch down. There are five different levels to choose from, with ‘max auto’ the one to use on slick runways. The same setting on a dry runway would leave a nose print in the setback in front of you, however.

To manually operate the brakes, pressure is applied to the top of the rudder pedals with your toes which, if they were selected, will also kick off the autobrakes. We generally don’t manually apply brakes until we’re below 100 knots. Pilots can even control the right and left brakes independently by pressing the tops of the right or left rudder pedals.

Reverse thrust

The noisiest, and third most effective way to stop an airplane on the ground is to use reverse thrust. This is done by lifting some handles that are in front of the thrust levers (throttles) when they’re at idle. The farther we pull these handles, the more thrust is deflected forwards to slow the jet. If these devices are inoperative, or a specific airport has restrictions on their use during late night hours, only 400 to 600 extra feet are needed for landing.

As we slow through 80 knots, we’ll bring the reverse thrust to idle and coming through 60 knots we are advised to stow the reverse thrust sleeve completely.

Here is a video of the reversers in operation that I caught while mechanics were making adjustments.

All of these methods can be seen in this picture of the center console of a Boeing 757:

Aerodynamic braking

There’s actually a fourth method of slowing an airplane after landing, but it’s generally not effective in the airline world, and more often seen when watching the Space Shuttle land. Aerodynamic braking is when the nose wheel is held high off the ground to use the drag of the airplane as a way to slow down. It’s not really effective, and it delays our ability to use brakes (and reverse thrust on the MD-80) while the nose wheel is still off the ground.

To taxi to the gate, the captain will use a combination of throttle and brakes to control the speed, which the FAA says shouldn’t exceed that of a person walking briskly. In reality, five to fifteen knots while taxiing is far more common.


So there you go. Oh, and congratulations on your recent jet acquisition. Or for those of you just worried about an Airport ’75 event occurring on your next flight, this could come in handy.

Either way, stay tuned for some more obscure airline flying tips!

Cockpit Chronicles takes you along on some of Kent’s trips as an international co-pilot on the Boeing 757 and 767 based in New York. Have any questions for Kent? Talk to him on the Cockpit Chronicles Facebook page or follow Kent on Twitter @veryjr.

Man sues Canadian airline because they refused to look at his penis

When Marcel Cote was in his Air Transat seat back in February 2008, he felt some discomfort “in the area between his legs”. He went to the washroom and noticed he was bleeding from his genitals.

He then asked a female flight attendant to send one of her male colleagues, and asked him to examine his bleeding penis.

As can be expected, the flight attendant refused, and handed him some absorbent paper instead. Upon landing, Mr. Cote was transferred to a local hospital, where doctors determined he had a ruptured vein.

Apparently, not having your genitals examined by a flight attendant is enough to sue the airline. Never mind that the flight crew is not trained to perform medical inspections, Mr. Cote claims the incident turned his vacation into a nightmare, and demanded $8,000 (CAD) for the “anguish” he suffered.

Thankfully, the Canadian judge rejected the case, issuing the following statement:

“It was not incumbent upon a flight attendant to conduct the medical examination of a passenger, a measure reserved for the medical profession,”

The judge didn’t deny that Mr. Cote was in some kind of discomfort, but she also maintained that his discomfort did not appear to be a life threatening situation.

Air Transat makes emergency landing for sick passengers

A plane flying from the Dominican Republic to Canada made an emergency landing Tuesday night in Florida when several of the passengers became ill. When the Air Transat Flight 477 landed at Fort Lauderdale/Hollywood International airport, eight passengers were wheeled off to the hospital as a precaution.

The Center for Disease Control stated that they were not sure what caused the illness but that it appeared to be something the passengers ate or drank. I was tempted to make a comment about the state of airplane food, but it turns out they were all family members who had eaten together before boarding the plane.